AER AER Domino 3

Presenting the Domino 3 by AER Acoustic Solutions From AER: "We are very happy that you have chosen the Domino 3. You are now the owner of a professional, compact and powerful 2x85 watts stereo amplifier. Each of its four discrete channels has its own EQ, Mute/Colour/Pad-switches, 48V phantom power etc. In addition the internal AER 32 bit digital effects may be separately configured via software and a USB connection and then individually blended for channels 1&2 plus channels 3&4 at the amp. We wish you hours of happy playing with your Domino 3!" Inputs, channels Combo socket, XLR + jack ¼” (6.35 mm) 1 – 4 Line mode High impedance, unbalanced jack input for instruments (pick-ups) and line-level sources Sensitivity: 26 mV (–32 dBV) Pad switch (attenuator): –10 dB Impedance: 1 Meg Equivalent input noise, A-weighted: 1.6 µV (–116 dBV) Phantom power: +9 V DC at ring of jack sockets in Ch. 1 and Ch. 3, switchable per channel (note 4), max. 100 mA (all channels total), overload protected Mic mode XLR (balanced), stereo jack (balanced), or mono jack (unbalanced) input Sensitivity: 7.5 mV (–43 dBV) Pad switch (attenuator): –19 dB Impedance (balanced): 1.7 k Equivalent input noise, A-weighted: 0.3 µV (–130 dBV) Voice filter: –4 dB at 450 Hz (referred to 10 kHz) Phantom power: 48 V, with common on/off switch for all four channels (note 4) Clip indicator: Headroom 6 dB Return Stereo return from external parallel effect loop 2 x mono jack, ¼” (6.35 mm, left/right) Sensitivity: 375 mV Routing: stereo to speakers, headphones, rec out, and L/R-out; mono (L+R) to DI out Aux in Auxiliary stereo input (e.g., for CD player) Level adjustable Cinch (RCA) sockets (left/right) Sensitivity: 375 mV Routing: stereo to speakers, headphones, rec out, and L/R out; mono (L+R) to DI out Outputs (note 3) Tuner Tuner output, not affected by mute switch Mono jack, ¼” (6.35 mm) Output voltage: 360 mV Headphones Headphones output. When connected, internal speakers are muted. Stereo jack, ¼” (6.35 mm) Output power: max. 2 x 100 mW / 32 ohms Input sensitivity for 2 x 50 mW / 32 ohms: 30 mV at line input (any channel) Caution: For stereo headphones with stereo jack plug only. Do not connect mono plugs. Active speaker Mono (L+R) output post-master, suitable for active extension speaker Mono jack, ¼” (6.35 mm) Output voltage: 1.4 V Activates 100 Hz low-cut filter for internal speaker if plugged in. L/R-out Stereo line output after tone controls, with aux in and effects Level adjustable by pre out 2 x mono jack, ¼” (6.35 mm, left/right) Output voltage: 0…1.4 V Rec out Recording output after tone controls, with aux in and effects Cinch (RCA) sockets (left/right) Output voltage: 1.4 V (note 4) DI Balanced XLR output before master, after tone controls, with aux in and effects (note 4) Level adjustable Output voltage: 0…145 mV Send Send for parallel effect loop Mono jack, ¼” (6.35 mm) Output voltage: 710 mV (note 4) USB lamp DC output for a lamp Data lines are not connected. Output voltage: 5 V DC, max. 200 mA Insert points Insert L/R Stereo insert point after master volume 2 x stereo jack (L/R), ¼” (6.35 mm) Tip = send, ring = return Output voltage: 1.4 V Tone controls (all channels) colour +10 dB at 8 kHz, –3 dB at 700 Hz bass ±8 dB at 100 Hz, shelf type middle ±4 dB at 650 Hz treble ±9 dB at 10 kHz, shelf type Effects Internal effect AER 32-bit digital effect processor with 16 factory presets Two independent, simultaneous effects (one for channels 1 and 2, and one for channels 3 and 4). USB interface and PC software for creating user- defined settings External effect Parallel effect loop (see send and return) Power Power amp 2 x 100 W / 4 ohms, discrete bipolar transistor design Dynamic range: 100 dB (A-weighted, see note 2) Limiter threshold 2 x 85 W Analog signal Subsonic filter, low distortion RMS limiter processing Speaker system Two 8” (200 mm) twin cone full-range speakers, bass reflex enclosure Mains power Mains voltage (depending on model): 100, 120, 230, or 240 V AC, 50–60 Hz. Power consumption: max. 420 W Mains fuse 5 x 20 mm Slow 3.15 A for 230 and 240 V models Slow 6.3 A for 100 and 120 V models General Cabinet 15 mm (0.6”) finnish birch plywood Finish Waterbased acrylic, black spatter finish Dimensions 365 mm (14.37“) high 420 mm (16.54“) wide 300 mm (11.81“) deep Weight 16 kg (35.3 lbs)